home
***
CD-ROM
|
disk
|
FTP
|
other
***
search
/
OS/2 Arsenal
/
OS2 Arsenal v1.0 (Disc 1)(Arsenal Computer).ISO
/
os2_drvr
/
4076cos2.exe
/
PTOS2.ZIP
/
AESOS2.ZIP
/
lexaes.msg
(
.txt
)
< prev
next >
Wrap
OS/2 Message File
|
1993-02-25
|
4KB
|
85 lines
MKMSGF
ILexmark AES Utility
I(C)Copyright Lexmark International Inc., 1991,1992,1993
ILicensed Material - Program Property of Lexmark, Inc.
I (Version 4.0)
IE%1 Port was not setup in OS2SYS.INI. Re-Install AES or Setup via the OS/2 Control Panel.
EAttempt to setup Serial Port %1 failed. DosExecPgm RC = %2.
EUnsupported Printer parity value found for the %1 Port.
None, Even, or Odd only supported.
EUnsupported Printer word length value found for the %1 Port.
7 or 8 data bits only supported.
EUnsupported Printer stop bit value found for the %1 Port.
1 or 2 stop bits only supported.
EUnsupported Printer handshaking method value for the %1 Port.
Hardware or Xon/Xoff only supported.
E%2 Baud is not supported by the Printer on Port %1.
Select 19200, 9600, 4800, 2400, or 1200 Baud from the Control Panel.
E%2 Baud is not supported by the Printer on Port %1.
Select 38400, 19200, 9600, 4800, 2400, or 1200 Baud from the Control Panel.
EDosFreeModule RM Call Failed with RC = %1
EDosGetProcAddr Failed Looking for MonBegin Routine with RC = %1
EDosGetProcAddr Failed Looking for MonEnd Routine with RC = %1
EDosGetProcAddr Failed Looking for AESResetRM Routine with RC = %1
:Debug Message ... %1
:%1 %2
EAES cannot be installed! AES must be installed before Resource Manager.
Close Resource Manager, then install AES. Once AES is installed, Resource Manager can then be re-installed. RC = %1
ENot enough parameters specified on the command line.
EFirst character of a parameter doesn't begin with a /.
EThe /R option should be the only parameter.
E"%1" invalid. Valid values are /LPT1, /LPT2, /LPT3.
E"%1" invalid. Valid values are /COM1, /COM2, /COM3.
EConfiguration file name can only have 80 characters in it.
EConfiguration file name format is /F=FILENAME.EXT.
EIllegal hexidecimal string in mode switch command.
ENot an even number of ASCII characters to convert to hex.
ELast character of hex data wasn't a single quote (').
IBinary Mode = ON
EDosSemSet failed with RC = %1.
EUnable to set PIPE semaphore. RC = %1.
EMonitor Open on %1 failed with RC = %2.
EMonitor Register on %1 failed with RC = %2 ; Size0= %3 ; Size1= %4 ; Loc= %5.
EUnable to open AVAIL semaphore. RC = %1.
EError allocating stack for %1 thread. RC = %2.
EError creating %1 thread. RC = %2.
ESemaphore create failed with RC = %1.
EUnable to wait for PIPE semaphore. RC = %1.
EUnable to get control back from monitors. RC = %1.
:~Remove AES
:To Display Mode Assignments, Select a Physical Printer Port:
:Emulation Mode Port Assignments
EUnable to read pipe from new instance of AES. RC = %1.
EUnable to write pipe to new instance of AES. RC = %1.
EIncorrect syntax for /S parameter. /S=2 or /S=OFF are valid examples.
EUnable to OPEN device %1. RC = %2.
EDosMakeNMPipe failed. rc = %1.
EDosOpenSem failed with RC = %1.
EUnable to clear PIPE semaphore. RC = %1.
EDosConnectNMPipe failed. RC = %1.
EDosDisConnectNMPipe failed. rc = %1.
EDosOpen failed on file "%1".
EError closing file "%1". RC = %2.
EDosSetPrty failed. RC = %1.
E%1 - Unable to get monitor packet from the chain. RC = %2 ; X = %3.
E%1 - Unable to send monitor packet down the chain. RC = %2; LOC = %3.
E%1 - Unable to request semaphore. RC = %2.
E%1 - Unable to clear semaphore. RC = %2.
E%1 - Unable to write data. RC = %2.
EInvalid option "%1".
EFormat is /T=y (to enable timeout) or /T=n (to disable timeout).
EError in DosGetVersion RC = %1.
EIncorrect OS/2 Version.
E%1 - Only %2 of %3 bytes written.
EAES program already running. Use /R option to end program.
EThe output port must be a member of the configuration file.
EToo many devices specified in configuration file.
EThe /I option should be the only parameter.
EFormat is /S=y (to enable data shifting) or /S=n (to disable data shifting).
IAES program is running.
IAES is controlling a printer on the following physical ports:I
EReturn code %2 returned trying to open %1.
IThe physical port is %1IBaud = %1IYou are about to end the AES program. Make sure all printing has completed and the spooler is idle.
E/P%1 is an invalid option.
EInput Parameter Error. The /S value valid range is 0 to 255.